It was unprocessed and could not be installed. The position of the hole on the Left Side of the Gap interferes with the protrusion of the OEM Cowl and cannot be tightened by Bolt. Improvements? The Left Side (STAND side) hole must be extended.
Everything else was fine.
As a side note, I liked it shorter, so I cut about 5 cm from the back to install it.
There was no Fitting problem with AKRAPOVIC I was lucky although I was preparing some processing for installation. However, we use separately sold for Full Exhaust SystemExhaust Bracket Because of that, there is a possibility that the angle has changed slightly. Clearance of Cowl and Muffler pipe section is one index finger Is not there Limit. If you were considering installing AKRAPOVIC at the same time, please refer for your reference.View Detail
The finish is as good as I expected.The H2 model is popular in Korea.There's a lot of interest in undercolls. I'm also using a-tech productsI have placed an order.The overall packaging of the cowl is well done, and the clear layer is also good.The carbon pattern is also well expressed.It will be installed after PPF film construction.Thank you.View Detail
Bellypan is very good quality, it's very easy to fit.Best to buy it already sprayed in the correct colour as Kawasaki do not tell you the colour code. View Detail
z900rs 21년식 에보니 컬러 순정머플러 차량 장착 후기입니다우선 구성품은 언더카울 방열스티커? 에이테크스티커 설명서 볼트류들이 전부입니다설명서에 사진과 설명이 있지만 사진이 약간 더 자세히 나와있으면 더 좋앗을꺼 같습니다작업시간은 30분 정도라고 명시 되어잇지만 처음으로 자가설치를 해서그런지 둘이서 2시간 조금 안되게 걸렷습니다그 이유는 제품이 순정대응임에도 불구하고 조금씩 구멍이 잘 안맞아서 볼트를 체결햇다가 풀엇다가 햇으며 순정 중통이 언더카울과 너무 딱 붙어잇어서 구성품에 포함되어있던 방열스티커를 붙이느라 다시 해체햇다가 달앗다가를 반복햇습니다 그 이외에는 구멍을 맞추느라 조금씩 애를먹엇지만 그래도 별도의 가공은 따로 하지않고 장착햇습니다 장착을 하니 확실히 더욱더 꽉찬 모습이 확실이 이쁘고 마음에 들긴합니다다만 다음 엔진오일 교체주기에 또 다시 풀고 장착할 생각을 하니막막하기도합니다 이상입니다,,,,,,This is a review of z900rs 21 year old ebony color genuine muffler vehicle installation.First of all, what is the under cowl heat dissipation sticker? A-tech sticker manual bolts are allThere are pictures and descriptions in the manual, but it would be better if the pictures were a little more detailed.It is stated that the working time is about 30 minutes, but it took less than 2 hours with two people because it was the first time I installed it myself.The reason is that, despite the fact that the product is genuine, the holes did not fit well, so I tightened the bolts and then loosened them. I repeated the adda. Other than that, I had a little trouble aligning the holes, but I installed it without any additional processing.When I put it on, it definitely looks more full, it's pretty and I like it.However, I am thinking of unscrewing it and installing it again at the next engine oil change interval.It's hard, it's more than that,,,,,,View Detail
A-Tech Twil wave carbon for Yamaha XJR 1300.Part is exellent quality and final finish of the prodilict is immaculate.Fitting is easy as the part is exact match for frame.EXELLENT View Detail
일본
최대 쇼핑몰
전용 쿠폰,
세일
빠르고, 안정적인
배송