- 적합:
- その他 TDMR Carburetor MIKUNI
- その他 TMR Carburetor MIKUNI
I used one of these for my needle seat on my dragstar 1100 carb. works great. Don't forget to lube it just a little to ensure a better seal. 자세히보기 - 적합:
- その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35 MIKUNI
It would be helpful if you could include it in the LongIdle Adjuster for TMR as a separate accessory part.In the case of TMR, it is difficult to lose as a top cover screw, so there is little chance of...자세히보기 - For YOSHIMURA Mikuni TM-MJN24It was chewing air, so I installed it on an Izumi F26.Quality was not a problem.Low prices and Quantity:I bought about 1 set of 4pcs. because the price is similar everywhe...자세히보기
- 적합:
- その他 TMX Carburetor for Φ30 MIKUNI
It does not seem to be discontinued by SEA BASS.It hits 13200-08D00.The one that hits 13200-08D01 is Needle for 6DHY36, but I could not find this one anywhere.The same Needle that was removed was visi...자세히보기 - 적합:
- DUCATI 900SS 91-97
If you miss it, it could be a year-long wait. I was told by a Motorcycle shop friend of mine that I should do it anyway, so I made up my mind to do it. I left the installation and setting to him.This ...자세히보기 - I bought this for a YamahaEF5500Ise carburetorfor repair.First, I looked up YamahaOEM Parts from the Parts List, but they are expensive as an O-ring at nearly 500 yen per piece, which is large for an ...자세히보기
- 적합:
- その他 TMR carburetor for multi/big body φ36/φ38/φ40/φ41 MIKUNI
Quantity:Quantity, which is useful in Set but also a waste because not all Packings have the same lifetime.:Set. special Packing of VSeal and cores also Quantity:I would like it to be a Set.자세히보기 - This is a washer for the adjust screw of the idling adjustment part of TZ-MJN24.Many used products are not fitted after OH, or are not fitted in the first place.Although it is a humble part, it is pro...자세히보기
- This is the O-ring that surrounds the Needle Valve of the TM-MJN24.I would like to avoid reusing this part, which is also related to Overflow, after carburetorOH, so I appreciate this low price.After ...자세히보기
- 적합:
- その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35 MIKUNI
It's a Mikuni OEM, so it's not a problem, but it's a little larger than the Drain bolt groove.자세히보기 - I bought this for a Gasoline leak on my TM-MJN24.The size is Exactly right, but it is a paper gasket, so it is very difficult to remove the old gasket if you have installed it for many years.자세히보기
- 적합:
- その他 TM(RS) carburetor for single/big body φ36/φ40 MIKUNI
Since it is a Racing carburetor, I had to OH it at least once a year, so I bought this Kit.It's easy to understand because we have all the consumable parts you need.자세히보기 - 적합:
- その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35 MIKUNI
Used for TMR's RemoteControl Idle Screw installation.As described in YOSHIMURA, when I used NORMAL screw, I was worried about the screw mountain, so I changed to Top screw and installed it.자세히보기 - 적합:
- その他 TMR Carburetor Small Body Φ28-Φ35 MIKUNI
I replaced the Throttle on my TMR34 because it wouldn't return to the end and the Idling stayed up around 2000rpm.This part is worn out in TMR. There were some bumps here and there, so I shaved them o...자세히보기 - 적합:
- その他 TM carburetor for Φ30 MIKUNI
- その他 TMX Carburetor for Φ30 MIKUNI
This is the E Ring that is often dropped and lost when removing the Jet needle from the TMX30 while rosing it! [Laughs]I bought it as a backup!자세히보기 - 적합:
- その他 TMX Carburetor for Φ30 MIKUNI
This part is a TMX30 SlideValve Spring receiver and Jet needle stopper.:I replaced it because it's Plastic and I'm worried about deterioration.자세히보기 - 적합:
- その他 TMX Carburetor for Φ30 MIKUNI
This is the TMX30 sold by Mikuni.This is the second time I've replaced the Hose on my Power jet.The replacement Cycle might be a little early because it deteriorates by the ultraviolet rays outside.자세히보기 - 적합:
- その他 TMX Carburetor for Φ30 MIKUNI
The TMX30 sold by Mikuni has become old, so I decided to overhaul it.The entire Needle Valve is also replaced.Now there's no Trouble!자세히보기 - 적합:
- その他 TMX Carburetor for Φ30 MIKUNI
TMX30 sold by Mihara is getting old.I also replaced the inside of the Needle Jet tube as it wears out.자세히보기 - 적합:
- その他 TMR Carburetor Big Body Φ36-Φ41 / Small Body Φ28-Φ35 MIKUNI
It is for TMR but the part number is the same as TMX30 Idle Screw.If you install it, it's the same and it's Large sturdy.Packing itself is Material:It's Plastic and I replaced it before it deteriorate...자세히보기
일본
최대 쇼핑몰
전용 쿠폰,
세일
빠르고, 안정적인
배송