TANAKA TRADING 닥스용 Φ26 프런트 포크용 헤드라이트 브래킷
The top mount is not in center, they've managed to fasten it way off to the side. They also messed up when welding one of the nuts for the headlight mounting bolt, here they melted the outline of the ...
* 더 좋은 그리고 반드시 일본 부품을 찾을 수 있는 스토어.
* 지금 등록하기 면어메이징 딜 및 특가 제공!
* 800,000이상의 상품 목록. 부품 찾기가 어렵지 않습니다.
축하합니다! 고객님의 새 계정이 성공적으로 만들어졌습니다! 이제 회원 특권을 이용하여 온라인 쇼핑 경험이 가능합니다. 온라인 상점의 운영에 대해 궁금한 점이 있으면 Webike에게 이메일을 보내 주십시오.
제공된 이메일 주소로 확인 메시지가 전송되었습니다. 네가 만약 한 시간 내에 메일을 받지 못하면, 부탁드립니다 문의하기.
The top mount is not in center, they've managed to fasten it way off to the side. They also messed up when welding one of the nuts for the headlight mounting bolt, here they melted the outline of the ...
First of all, it is a very beautiful baking color and Exhaust pipe Design ○ It's made of bar. I use it in 88? But the sound quality from Idling is an explosive sound Silencer part is a rough strai...
Current situation, I can not do until installation, but in bullets? Screw preparation is necessary separately for installation.From the finish of the appearance, I thought that it disgusted? Long Scre...
Originally a product of for MONKEY, Footpeg Bracketetc. You can install it without problems if you process it somewhat.OEM is Material : Rubber 's tasteless shape, return spring at the time of fol...
Nice and glossy, i think it is the best part of my monkey. The tank's price is very reasonable while the appearance is really really cool. Good choice!
Since I attached 53 Seat to LITTLE CUBFI I purchased it instead of OEMRear Carrier.However, because the accuracy is poor, there is no size at all and can not be installed as it is, so it will be proce...
When I search with CROSSCUB 110, I bought this product because it came out. However, the worst! Size does not match at all, a new product CROSSCUB 110 is scratched, and it turns into a painted baldnes...
I think that it should be written in the description that Headlight Bulb is a standard that is not normally used in Japan. This is horrible..In the light case, the part that sprites Meter pulling Mete...
Oil seal and hexagon socket M6 length 2 cm long Screw requiredAlso, since Nut stopping Camshaft Chain Cover was about 3 mm long, I put Aluminum 5 mm Washer and adjusted it. Perhaps Oil will leak if it...
I put it on CUB 90, but it is normal and it is normal without permission.If you do not do Clear blinker, you do not need Orange balls ...Rather, I wonder if there is an ordinary ball of VERSION.I have...
It takes more than 4 days for delivery, it is ineffective with defective items!To be honest, it was disappointing. For the time being, Pipe was connected upside down, the cracks were blocked with Viny...
Since I am a maintenance beginner, when I first used it, I was pretty worried because I would beat Motorcycle Body, but once I grab hang, I could easily raise both Rear and Front!
Drawing difficult to see translation (Please do not enter here. I ordered a certain famous thing immediately after using it. I immediately removed it from my favorite car It was a loss of cheap buying...
You had better quit dual use.I can still use Rear, but Front does not feel like going up.Forcibly raised Motorcycle collapsed.On the contrary it was expensive shopping.After all, I replaced a famous M...
Compatibility with air-cooled Kawasaki ◎?Assembled for 3 minutes, with Center Stand combined, heavyweight cars got a little up in one handMaintenance efficiency Up mistake ♪
I think that the price and the commodity are like this if only once. After opening the stage Ball, it was in the state of RoseRose. But the price was also cheaper and it was a product. But it was good...
I bought it for GSX-R 750 and WR 250 X, but it was short in the back, I was disappointed without getting stuck in front.First, the back is 17 Inch wheel but avoiding Axle Shaft is difficult to make it...
I bought it to lift the Front of HORNET.I think that Rear stand is essential as it will become Front up after lifting Rear.In the case of HORNET, it seems to be in contact with Front fender when insta...
You can make it cheaply.When I use it for Rear stands, I feel that I want a bit more height in my MotorcycleEven if you shake it during use it is a nice feeling without anxiety.
There was only an assembly drawing, but I was lost as to how to use itUnder bracket Because Arm inserted under is FreeI will only raise it after plugging in.It got so light as I was beat fast.
First of all, packing was good, but since the width of Pipe used for Front did not match at the time of assembly, it was multiplied by force technique and weight. Next, when the rod to be inserted in ...
일본
최대 쇼핑몰
전용 쿠폰,
세일
빠르고, 안정적인
배송