CB750FZ에 스즈키 GSX750S카타 내셔널 1100S일본도 용의 스윙 팔을 장착 가능하게 하는 칼라입니다.
좌우 비대칭 CB-F스윙 암에 대해서 카타나 스윙 팔은 좌우 대상입니다.
이 문제를 해결하기 때문에, 좌우의 컬러 폭을 바꾸고 일본도 스윙 암을 오프셋 장착.
휠 센터, 체인 라인 함께 정규의 위치며 CB-F의 정품 휠 및 브레이크 주위의 볼트 온 장착을 가능하게 했습니다.
스윙 암의 좌우 위치를 조정하는 색상은 강도를 고려할 재질은 스틸로 하고 녹을 억제하기 위해서 표면은 도금 처리를 하고 있습니다.
또, 니들 베어링 부분에는 담금질 처리된 컬러를 채용했습니다.
일본도 스윙 팔에 교환했을 경우, 바퀴, 휠 컬러류, 캐리 퍼 서포트, 토오크 로드는 CB750F/CB900F의 것이 그대로 장착 가능합니다.
피벗 샤프트는 CB750FZ용을 사용, 액슬 샤아 프트는 CB-F용, 일본도용 모두 사용 가능합니다.
또, 스윙 암의 피벗 부분의 캡, 피벗 내부의 컬러 및 체인 어저스터는 카타나용을 사용하세요.
취급 설명서를 부속되어 있습니다.
[스윙 암의 서비스 받은 부분의 부시 폭에 대해서]
사스함의 부시는 CB-F용의 순정 부시 타치카에루, 일본도용의 부시를 사용하는 경우는 19mm폭까지 깎아 주세요. (*화상 5참조)
*CB-F용의 순정 부시 품번은 40548-268-000 (CB750FZ용] 라고 52451-357-000 (CB750FA-FC용] 의 2종류가있습니다만, 모두 사용 가능합니다.
(부시 경계부의 폭이 CB750FZ용(18mm) , CB750FA-FC용 (16mm) 이 됩니다만, 부시 중앙부의 폭 (19mm) ·안지름 (10mm) ·외경 (22mm) 는, 어디 부시도 동촌 법 때문)
This is a collar which enables to install Suzuki GSX750S Katana 1100S Katana swingarm on CB750FZ.
The Katana swingarm is designed to be used with the asymmetrical CB-F swingarm.
To solve this problem, the width of the left and right collar is changed to offset the Katana swingarm.
Both the wheel center and chain line are correctly positioned to allow bolt-on installation to the stock CB-F wheels and brakes.
The collar to adjust the position of swingarm is made of steel for strength and plated surface to prevent rusting.
In addition, a hardened collar is used for the needle bearing part.
If you change to Katana swingarm, wheel, wheel collar, caliper support and torque rod of CB750F / CB900F can be used.
Pivot shaft is for CB750FZ and axle shaft for CB-F and Katana are both usable.
The cap of the swingarm pivot, the collar inside the pivot and the chain adjuster must be used for Katana.
Comes with an instruction manual.
[About the bushing width of the swingarm suspension support part]
The bushing of the suspension support should be replaced with the stock bushing for CB-F. Or, if you use the bushing for Katana, cut it down to 19mm width.(*See image 5)
*The stock bushing part number for CB-F is 40548-268-000 [for CB750FZ] and 52451-357-000 [for CB750FA-FC], both of them can be used.
(The width of the outer circumference of the bush is for CB750FZ (18mm) and for CB750FA-FC (16mm), but the width (19mm), inner diameter (10mm) and outer diameter (22mm) of the center of the bush are the same for both bushes)