ShieldLens with Light Sensitive 기능은 햇빛의 강도에 따라 렌즈의 강도를 변경합니다..
Helmet Levels 내부와 외부의 공기 온도 차이를 붙여 적층 구조 만들기..
추가 안개 방지 처리.
경주 투어에서 아마추어에서 탑 라이더까지 큰 돈으로 신뢰받는 가장 강한 렌즈 체험.
방패의 뒤쪽에 붙이는 것만으로 쉽게 설치.
【PROGRIP 3000LS 렌즈 사용 설명서】
이 혁신적인 렌즈는 헬멧의 방패에 장착 한 후 안개와 일조 상태가 다른 여러 조건에서 방패의 성능을 향상시킵니다.
3000 LS를 실드에 부착하기 전에 다음 취급 설명서를주의 깊게 읽으십시오..
■ 예비
시원하고 건조하며 먼지가없는 곳을 선택하십시오..
헬멧의 방패를 내리고, 방패의 입구를 따라 마스킹 테이프를 붙여주십시오. (패키지 다이어그램 참조).
실드를 제거하면 3000 LSLens의 정확한 설치 위치를 표시합니다.
헬멧에서 방패를 꺼내십시오..
제조사의 지시에 따라 쉴드를 닦고 말리십시오..
실드 · 지저분한 지문 · 물방울이 남았는지 확인하십시오.
실리콘 표면 처리 된 실드 세정에 대한 3000 LS의 접착력을 향상시키기 위해, (규산염을 함유하지 않음) 석유 계 플라스틱 세정제를 권장합니다..
실드 세척 · 건조 후 3000 LSLens 설치.
■ 설치
1. 렌즈 양면 보호 필름 제거.
이 경우 렌즈에 지문이나 먼지가 끼지 않도록주의하십시오..
렌즈의 양면 · 우리는 또한 끈적 거리는 개스킷으로부터 보호 필름을 제거합니다..
2. 렌즈를 양쪽 끝으로 잡고 양면 테이프가있는면이 방패의 안쪽을 향하도록 U 자 모양으로 천천히 렌즈를 굴 리십시오.. (패키지 다이어그램 참조)
삼. 렌즈를 붙여 넣은 다음 정확한 위치에 배치하십시오. 수량 : 렌즈가 세팅되어 있는지 확인하고 렌즈 주위로 부드럽게 힘을 가하십시오..
붙여 넣기 위치가 바뀌면 이동 한 부분을 가볍게 들어 올린 후 부드럽게 전원을 다시 추가하십시오..
4. 정확한 위치에있는 렌즈 수량 : 세트 후, 이번에는 렌즈 주위 전체에 힘을 가하고 접착제 가스켓을 단단히 붙입니다.
렌즈를 방패에 단단히 부착하기 위해 방패를 다시 헬멧에 부착하기 전에 24 시간 동안 기다려주십시오..
5. Shield를 HelmetBody에 장착 할 때 3000 LSLens가 HelmetBody의 Shield베이스 등의 위치에 따라 몰딩 부품을 간섭 할 수 있습니다...
실드가 열렸는지 확인하십시오. / 방해하지 않도록 쉴드베이스 등의 조정을하는 동안 문제없이 닫을 수 있습니다..
■ 정비
렌즈에 남아있는 먼지는 유리 세제를 사용하여 제거 할 수 있습니다..
부식제가 포함 된 연마제 나 세제를 사용하지 마십시오..
Shield lens with light sensitive function that changes the intensity of the lens depending on the intensity of sunlight.
A laminated structure is created by attaching this product to a helmet to equalize temperature difference between inside and outside of a helmet and prevent fogging of a view through a shield.
Also anti-fog treated.
From touring to racing, from amateurs to top riders, experience the most powerful lens that is trusted by all.
Easy to install, just stick it on the back of the shield.
[instruction manual for PROGRIP 3000LS LENS]
This innovative lens, after being attached to the shield of a helmet, enhances the total performance of the shield in various conditions with different fog and sunshine conditions.
Please read the following instructions carefully before attaching the 3000LS to the shield.
■Preparation
Please choose a cool, dry and dust-free place for installation.
With the shield of the helmet lowered, apply the masking tape along the opening of the shield (see the figure on the package).
When the shield is removed, the exact mounting location of the 3000LS lens will be noted.
Remove the shield from the helmet.
Clean and dry the shield according to the manufacturer's instructions.
Please make sure that there are no fingerprints, oil stains or water droplets on the shield.
For cleaning shields with a silicone surface treatment, we recommend a petroleum-based plastic cleaner (without silicates) to improve the adhesion of 3000LS.
Please install the 3000LS lens after cleaning and drying the shield.
■Installation
1. Remove the protection film from both sides of the lens.
Be careful not to get fingerprints or smudges on the lens.
Remove the protection film from the adhesive gaskets on the sides and around the lens.
2. Hold both ends of the lens and slowly curve the lens into a U-shape with the side with the double-sided tape facing the inside of the shield.(See diagram on package)
3. Once the lens is attached, make sure it is set in the correct place, and gently apply force to the entire area around the lens.
If the sticking position has shifted, gently lift up the misaligned position and gently apply force again.
4. After the lens has been placed in the correct position, firmly apply pressure to the entire area around the lens to ensure that the adhesive gasket is firmly attached.
Please allow 24 hours before attaching the shield to the helmet again in order to make the lens stick to the shield more firmly.
5. 3000LS lens may interfere with a braid depending on a position of a shield base of a helmet when a shield is attached to a helmet.
Please check if you can open and close the shield without any problem while adjusting the shield base to avoid interference.
■Maintenance
Residual dirt on the lens can be removed by using a glass cleaning agent.
Do not use abrasives or corrosive cleaning agents.