밸브형:H7 (2등)
소비 전력:40W
스페이서 없이
[치수]
·LED드라이버 본체 치수:세로 53.5mm, 폭 28.5mm, 두께 16mm
·LED방열 벨트 치수 기준:길이 (뿌리부터 첨단까지) 약 132mm, 두께 (편도 3장 분량) 약 5mm, 폭 9mm
·A:36mm, B:44mm, C:81mm
A:상부 좌면에서 밸브 끝까지 치수 (밸브 본체 치수)
B:상부 좌면에서 밸브 톱까지의 치수 (밸브의 헤드 라이트 셰이드 등의 간섭의 기준)
[세트 내용]
키트 1개
·취급 설명서
*렌즈 컷식 전조등에 대한 초점이 재현 못 하고 계측상 광축 창출할 수 없는 경우가 있습니다.
*프로젝터식 전조등에 관해서, Hi빔 부분에 사용은 최대 광도의 초점이 발생하지 않는 경우가 있습니다.
*클리어 렌즈 리플렉터식이라도, 리플렉터 면적의 작은 특수 형태의 전조등에 관해서는, 드물게 차량 검사 기준을 안 되는 광도 수치가 되는 경우가 있습니다.
* 많은 시험 차량에서 차량 검사 기준을 충족하고 있다는 사실을 확인하고있습니다만 어느 차량에도 반드시 차량 검사 기준을 클리어 하겠다는 100%의 보증까지는 말할 수 없으므로 양해 부탁 드립니다.
*주문 전에 항상 현차의 밸브 후부와 차량 주변 부분의 간섭 여부 확인과 밸브 형식의 적합성 확인을 부탁 드립니다.
*방열 벨트와 하네스의 처리를 고려하는 최소 A+15mm이상의 여유를 수납 공간으로 확보되는지 확인 바랍니다.
*밸브는 고열을 내므로 열으면서 기도에 의한 LED의 고장을 방지하기 위해B+10mm이상의 여유를 확보하는지를 확인 바랍니다.
*밸브 후부의 직경은 22mm에 공통적으로 되지만, 고열을 내므로 수납시는 주변에 여유를 둔 고려를 부탁합니다.
*LED드라이버 본체의 세로 치수는 배선을 포함하지 않으므로 드라이버의 수납 공간 확보 이외에 배선 처리의 여유 확보 때문에 최소한+40mm이상의 여유를 두세요.
*LED방열 벨트는 고열을 내므로, 주변 기기에 가능한 한열 트러블을 방지하기 때문에 공간에 여유를 가진 수납을 부탁합니다. (제품 로또 상황에 더 길이가 다소 전후할 수 있으므로 어디까지나 기준이 됩니다.)
Valve shape: H7 (2 lights)
Power consumption: 40W
Without spacer
[Size]
・LED driver main unit dimensions53.5mm (length), 28.5mm (width), 16mm (thickness)
・Approximate dimensions of LED heat dissipation beltLength (from root to tip): approx. 132mm, thickness (3 pcs. per side): approx. 5mm, width: 9mm
・A: 36mm, B: 44mm, C: 81mm
A: Dimensions from upper seat to valve end (valve body dimensions)
B: Dimensions from the upper seating surface to the top of the bulb (guide for interference of the bulb with headlight shades.)
[Set components]
・1 kit
・Instruction Manual
*For lens-cut headlights, it may not be possible to create optical axes due to the lack of reproducible focus and measurement.
*For projector type headlights, the use of the projector type headlights in the hi-beam area may not produce the maximum light intensity focus.
*We have confirmed that our products meet the bike inspection standards on many test bikes, but please understand that we cannot guarantee 100% compliance with the bike inspection standards for all bikes.
*Before ordering, please make sure to check whether or not the rear of the valve interferes with the surrounding parts of the bike and confirm that the valve type is compatible with the bike.
*Please make sure that there is at least A+15mm of space for storage, taking into consideration the routing of heat dissipation belts and harnesses.
*The bulb emits high heat. To prevent LED failure due to heat buildup, please make sure that there is a margin of B+10mm or more.
*The diameter at the rear of the valve is the same as 22mm, but it generates high heat, so please consider leaving enough room around the valve when storing it.
*The vertical dimension of the LED driver does not include the wiring, so please allow at least +40mm of space for the wiring as well as for the storage space of the driver.
*Since the LED heat radiation belt generates high heat, please make sure that there is enough space in the peripheral equipment to avoid heat problems as much as possible.(The length may vary slightly depending on the product and lot conditions, so this is only a rough estimate.)