평면연마는 물론, 자유도의 높이가 매력.
100mm디스크 그라인더용 금속용 연마 디스크
주로 용접 비드의 제거, 버 제거, 녹 제거, 평면 연마에 사용.
[특징 1, 평면 연마에 위력을 발휘]
주로 평면 연마에서 위력을 발휘.
숫돌덩어리보다 끝이 마일드하며 특히 평면돌출에 강한 것이 특징.
[특징 2자유도의 크기]
내부 기반이 튼튼하므로 밀어서 강하게 절삭할 수 있음.
각 제거에서 무리한 연마 절삭, 단면의 버 제거 등 올마이티에 사용할 수 있습니다.
[특징 3·토네이도 선더만의]
일반적인 것에 비해, 토네이드 썬더는 가장자리에 약간 기근이 맞지 않는 부분이 있습니다.
이것을 사용해서 더 부드럽게 사용할 수 있습니다
[특징 4·숫돌 지르코니아에 대해서]
연마포 숫돌은 지르코니아가 됩니다.
딱딱하고 중절삭에 적합하며 스테인리스 절삭에 강한 소재가 됩니다.
[디스크 그라인더의 회전 수에 대해]
저속 (저회전수) 사용하면 원심력이 작아지므로 연마 디스크와 피연마물의 접촉이 부드러워집니다.
이로 인해 특히 기반 고정 영향력이 작은 '소프트' '에어' 에서 연마포의 형상이 피연마물에 친숙해지기 쉬워지고, 곡면의 형상에 따른 연마절삭을 하는 것이 쉬워집니다.
또한 연마포의 비산에 의한 소모, 손상, 물림이나 걸림돌이 감소시킬 수 있습니다.
*마감시에도 균일하게 조작하기 쉬우므로 스크래치의 감소로도 연결됩니다.
반면 중절삭에 있어서는 취약해지고 회전수 감소에 의한 일량의 저하로 절삭속도가 늦어집니다.
'플랫' 특히 "컷" 은 일반적인 고속 회전형 사용을 권장합니다.
[저속 그라인더]
*변속 기능 포함, 저속 고토크형 디스크 그라인더와 스피드 컨트롤러의 사용이 일반적입니다.
[저속 고속과의 궁합]
저속 <-----> 고속
소프트/에어/플랫/컷
40/120/320
It is attractive not only for flat surface polishing but also for its high degree of freedom.
Abrasive discs for metal for 100mm disc grinders.
Mainly used for weld bead removal, deburring, rust removal and flat grinding.
[Feature 1 - Effective for flat surface polishing]
Mainly used for surface grinding.
It has a milder impact than a lump of whetstone and is especially strong in planing.
[Feature 2 - High degree of freedom]
Since the back base is solid, strong cutting is available by pressing against it.
It can be used for all kinds of applications such as corner removal, hard grinding and deburring of the end face.
[Feature 3 - Only with Tornado Thunder]
The Tornado Thunder has a small part on the edge that does not touch the base it, compared with the general one.
You can also use it to make it even milder.
[Feature 4 - Grindstone Zirconia]
The grinding wheel of the polishing cloth is zirconia.
It is hard and suitable for heavy cutting, and is a strong material for cutting stainless steel.
[About the speed of the disc grinder]
When used at low speed (low rotation speed), the centrifugal force is reduced and the contact between the grinding disc and the workpiece becomes softer.
This makes the shape of the abrasive cloth more familiar to the workpiece, especially in the "soft" and "air" types where the fixing influence of the base is small, and makes it easier to perform abrasive cutting along the shape of curved surfaces.
In addition, the wear and tear, damage, biting and snagging caused by scattering of abrasive cloth can be reduced.
*It is also easy to operate evenly when finishing, leading to a reduction in scratches.
On the other hand, in heavy-duty cutting, the cutting speed becomes slower due to weaker contact and lower workload caused by reduced rotation speed.
For "Flat" and especially "Cut", recommending the use of a general high-speed rotation type.
[slow grinder]
*It is common to use a disc grinder with variable speed function, low speed and high torque type and speed controller.
[compatibility with low and high speeds]
Low speed <--------> High speed
Soft / Air / Flat / Cut
40 / 120 / 320