라이트 유닛 포함
[치수]
폭: 약 760mm
전후 길이: 약 500mm
높이:약 520mm
[재료]
FRP
내용물
카울 본체, 스테이 세트, 스크린, 스크린의 나사 세트
*반드시 주의사항 확인 후 구매하시기 바랍니다.
*라이트는 '7인치 프로젝터 LED 헤드라이트 유닛' 및 같은 타입의 라이트 유닛을 사용.
* 본 카울은 해외산 범용제품이므로 구멍이 맞지 않고 흠집, 긁힘 등이 있어 장착에는 가공이 필요합니다. 아래 내용을 반드시 이해하신 후 구입 부탁드립니다.
*라이트 유닛과 카울이 간섭하는 경우가 있는데 그럴 경우 카울의 간섭 부분을 삭제해야 합니다
*포크와 카울이 간섭하는 경우가 있으며, 좌우 가동 범위를 확인하고 간섭할 때에는 카울을 깎아야 합니다.
*기타 간섭하는 부분은 절단, 깎는 등 가공해야 합니다.
*부속된 라이트 유닛은 메인 하네스에서 나오는 연장 하네스를 제작해야 합니다.
*카울의 위치내기에 따라서는 스테이와 카울의 구멍이 어긋나는 경우가 있습니다. 그 때는 카울의 구멍을 넓혀야 합니다.
*스크린과 카울의 구멍이 맞지 않을 경우가 있는데, 그 때는 카울 센터의 구멍에서 바깥쪽으로 웰넛으로 고정해 주시고, 맞지 않는 부분을 순서대로 줄 등으로 넓혀 나가야 합니다.
*로또로 인해 스크린용 홀은 카울쪽에 뚫리지 않은 것이 있는데, 스크린을 맞춰서 순서대로 홀 가공을 해주십시오.
여기에 기재 이외의 가공방법 등은 대답해드리지 않으므로 실차에 맞게 확인해 주십시오.
*가공을 전제로 한 상품이기 때문에, 장착이 되지 않는 등의 반품은 일절 접수할 수 없습니다.
*도장 전에 반드시 가공, 장착을 해주십시오. 도장 후의 클레임도 접수하지 않습니다.
*메이커의 사정에 의해 상품의 사양변경이 있을 수 있습니다. 양해바랍니다.
With light unit
[Size]
Width: Approx. 760mm
Front and rear length: Approx. 500mm
Height: Approx. 520mm
[Material]
FRP
Components
Cowl body, bracket set, windshield, windshield screw set
*Please make sure to read the notes before purchasing.
*7 inch projector LED headlight unit and the same type of light unit are used for the lights.
*Because this cowl is a universal product made non Japanese, it may have some scratches and scuffs, and the holes may not fit, so some modification is required for installation.Please make sure you understand the following information before purchasing.
*The light unit and cowl may interfere with each other, in which case it is necessary to shave the interfering part of the cowl.
*There is a case that the fork and the cowl interfere with each other, check the range of movement of both sides and if it interferes, it is necessary to shave the cowl.
*Other interfering parts need to be cut or shaved.
*The supplied light unit requires an extension harness to be fabricated from the main harness.
*Depending on the positioning of the cowl, the hole between the bracket and the cowl may be misaligned.To do this, you will need to widen the hole in the cowl.
*In some cases, the holes of the windshield and the cowl do not match, in that case, you need to fix the windshield with the well nut from the center hole of the cowl to the outside, and widen the holes with a file in order.
*Depending on the lot, some of them do not have the hole for the windshield on the cowl side.In this case, please drill the holes in order to match the windshield.
We will not provide information about processing methods other than those mentioned here, so please verify according to your actual bike.
*Any returns will not be accepted due to inability to install the product.
*Please be sure to process and install before painting.Any claims after painting are not accepted.
*There may be changes in product specifications due to the manufacturer's reasons.