* 피벗 부분이 상당히 굵어졌으므로 부속 롱 피벗 샤프트를 사용해 주십시오.
* 드럼기구 디스크기구에 관계없이 풋 브레이크기구에 가공이 필요합니다. 미리 양해바랍니다. (자세한 내용은 아래 설명을 참조해 주십시오.)
[설치에 대해서]
*오토바이 정비에 관한 경험자들이 맞붙을 수 있다 작업을 하세요.
* 스윙암의 길이가 연장되어 드라이브체인의 연장이 필요합니다.
*정품 액슬샤프트는 사용할 수 없습니다. 부속된 롱 액슬샤프트은 사용해주세요.
* 또한, 정품 피벗 샤프트도 사용할 수 없습니다. 부속의 롱 샤프트도 사용하세요.
드라이브체인의 칸수는, 고객의 차체컨디션이나 전후의 스프로킷에 따라 변화하기 때문에, 지엠트에서는 안내하고 있지 않습니다.
* 각 연장 타입별 장착 가능 휠 직경은, 사용하는 타이어의 편평율이나 휠폭 등의 조합에 따라 달라집니다.
와이드 휠에 대해서는 5.5J까지 장착 확인을 실시합니다. (신제품이므로 현상검증대기입니다. 양해부탁드립니다.)
* 휠의 중앙 위치 조정이나 체인 라인 조정, 브레이크 관련 부품의 위치 조정 등이 필요합니다.
*사용의 프레임과 본 스윙 암과 간극은, 좌우 각 0.5mm이상일 경우에는 세탁 등으로 틈새를 작게 하는 처리를 하세요.
*틈새가 큰 상태로 피벗 샤프트를 체메입은할 경우, 스윙 팔에 높은 부하가 걸리는, 최악의 경우, 파손될 위험이 있습니다.
*리어 서스펜션이 풀 최종 상태가 되어도, 비정상인 접촉 부분이 없는지 반드시 확인하고 주행하세요.
상품마다, 세세한 부분에서 약간의 사양 변경이 있는 경우가 있습니다. 소개영상과 다소 다른 점이 있습니다만, 실물을 우선으로 하오니, 양해 부탁드립니다.
*주행 개시 후에는 이른바 '초기 이완'의 발생에 유의하여 예기치 못한 트러블이 발생하지 않도록 세심한 점검을 실시해 주세요.
[보증에 대해서]
*수송 상의 문제로, 작은 기스와 찰과상이 발생하는 경우가 있습니다. 상품의 가치나 기능을 현저하게 해치는 오류 이외는, 보증 대상 외로 하고 잘 먹겠습니다.
* 장착의 여부는 치수 표시 등을 참고로 고객님께서 판단하시기 바랍니다.
그리고, 주행 시작 후의 트러블은 운전 상황 및 정비 상황, 혹은 차체 컨디션과 수급 불균형이 원인이 되는 일이 많고 상품 개별의 원인과 구별이 되기 어렵기 때문에 모든 면책으로 하겠습니다.
[ 구매전 주의사항 ]
* 지엠모토 상품은 모두 커스텀 파츠 입니다. 경우에 따라 폰츠가 불가능하거나 각처에 조정및 가공이 필요할수도 있사오니 오토바이정비에 관한 전문점에서의 조립작업을 부탁드립니다.
운송중에 발생하는 작은 상처, 미소한 찰과상, 또는 도장이나 도금의 경도한 얼룩등은 보증의 대상에서 제외하겠습니다.
차량번호 등록이나 보험가입, 수리작업 등, 고객자신의 판단으로 이루어진 비용에 대해서는 이유 여하에 관계없이 청구에는 응할 수 없기 때문에 주의해 주십시오.
*메이커의 사정에 의해 상품의 사양변경이 있을 수 있습니다. 양해바랍니다.
Manufacturer: KEPSPEED
Country of origin :China
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*Please use the supplied long pivot shaft as the pivot section is quite thick.
*The foot brake mechanism needs to be modified regardless of the drum or disc mechanism. (For more details, please see the explanation below.)
[About the installation]
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*The drive chain needs to be extended due to the extended swingarm length.
※Stock axle shafts cannot be used.Please use the supplied long axle shafts.
*Also, the stock pivot shaft cannot be used.Please use the supplied long shaft.
*The number of tentioners of the drive chain varies depending on the condition of the customer's vehicle and the front and rear sprockets, so GM-MOTO does not provide information on this.
*The installable wheel diameter for each extension type varies depending on the combination of flatness and wheel width of the tire used.
*For wide wheels, GM-MOTO will confirm the installation of wheels upto 5.5J.(This is a new product and GM-MOTO is waiting for verification.)
*It is necessary to adjust the center position of the wheel, the chain line, and the position of the brake related parts.
*If the gap between the frame and the swingarm is more than 0.5mm on each side, please use washers to reduce the gap.
*If the pivot shaft is tightened with a large gap, the swingarm will be subjected to a high load and may be damaged in the worst case.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.
※Please judge by yourself whether it can be installed or not referring to the size indication.
[Notes on purchase]
*All GM-MOTO products are custom parts.In some cases, it may not be possible to install it on the bike, or it may need to be adjusted or processed in various places.
*There may be changes in product specifications due to the manufacturer's reasons.
* Please note in advance that cancellation and/or return of this product cannot be accepted once the order has been placed.