[재료]두랄루민 A2017
[색깔]핸들바 : 검은
[표면 처리]스템 너트 : 경질 양극화 알루미늄
[핸들 위치]4-위치:스트리트 하이 (STD) *CAFE는 1개 포지션에서만 사용 가능
[핸들바 사이즈]
전체 길이 : 280mm
내경 : 16mm
[행 앵글]
거리 : +5도
레이싱 : -5도
[개방각/높이]무료
[핸들바 잠금]사용 가능
[핸들바 스톱퍼 기능]사용 가능
[베어링]
언더 브래킷 측면 : 사용 가능
상단 브리지 측면 : 사용할 수 없음 (재고 재사용)
[사양]
스톡 브레이크 마스터 지지대 : 사용 가능
스톡 클러치 홀더 지지대 : 사용 가능
BREMBOR RCS 브레이크 확인
라이트 브래킷, 미터, 경음기 등. 스톡 제품을 사용할 수 있습니다.
[포함된 부품]
전용 미터 브래킷
전용 칼라 세트
[브레이크] / 클러치]
위치에 따라 오일 탱크와 클러치 와이어가 미터기 커버를 방해할 수 있습니다.
브레이크 호스를 외부 호스로 변경하거나 경로를 변경해야 합니다.
[전선]
액셀러레이터 와이어, 클러치 와이어 및 스위치 케이블을 교체해야 합니다.
[위치 설명]
포크 클램프를 장착할 때 핸들 바 클램프 부착물이 위쪽을 향하도록 클램프 볼트가 바깥쪽을 향해야 합니다.
핸들 바는 널빤지 위치에서 +5도 방향으로 클램프합니다.
다른 위치는 공장 깜박임에 방해가 되므로 설치할 수 없습니다.
*자전거의 방향은 자전거에 발이 걸렸을 때 판단됩니다.
*Z900RS와 Z900RSCAFE는 호환 부품번호가 다르므로 확인 후 구매하시기 바랍니다.
*높이 및 너비가 진품에서 변경되기 때문에 공공도로 주행에 적응하기 위한 구조적 변화가 필요함. 구조변경을 신청하지 않고 자전거 등록정보를 변경할 경우 공공도로에서 이용할 수 없다.
*이 키트는 Z900RS CAFE 전용이며, 설치에 필요한 부품이 포함되어 있습니다.. 페어링이 없는 Z900RS의 경우 다른 부품 번호를 구매하십시오.
*Z900RSCAFE의 위치는 정품 블링커와의 간섭을 방지하기 위해 제한됩니다.. 구입하기 전에 다음 주의 사항을 확인하십시오.
*온리 스트리트 하이 (STD) 위치를 사용할 수 있습니다.
마스터 실린더 자체가 표시기에 가까우므로 마스터 실린더의 설치 각도가 제한됩니다.. 표시기에 닿지 않도록 각도를 조정하십시오.. (사진 참조)
페어링에 대한 간섭을 방지하기 위해 페어링, 미터 및 조명은 전방으로 상쇄됩니다.. (사진 참조)
리어 뷰 미러를 장착할 때 미러 클램프를 탈거해야 합니다.. 미러가 핸들 바에 고정되어 있으면 미러를 교체할 수 없습니다.. 미러 유형에 따라 페어링의 간섭으로 인해 설치가 불가능할 수 있습니다.
*경 브라켓, 미터기, 경음기 등 재고상품 사용이 가능합니다.
*핸들바는 고정 스위치 BOX이기 때문에 드릴링이 필요합니다.
*Under Bracket에는 Stock Clamp 볼트를 사용한다.
*바운드는 포함되지 않으며 별도 구매하셔야 합니다.
*설치를 위해서는 전문적인 지식과 도구가 필요하오니 설치 전문지식이 풍부한 전문샵에 문의하시기 바랍니다.
*사진에 표시된 거울은 Z입니다.II 타입의 짧은 브래킷.
*사진에 다른 부분이 포함되어 있을 수 있습니다.
*단일 영상은 컬러입니다.브라운 / 검정색.
*제조업체 사정으로 인해 제품 사양이 변경될 수 있습니다.
[Material] Duralumin A2017 material
[Color] Handlebar: Black
[Surface treatment] Stem nut: hard anodizing
[Handlebar position] 4 positions: Street Hi (stock) *CAFE only supports one position
[Handlebar Size]
・Total length: 280mm
・Inner diameter: 16mm
[Sweep angle]
・Street: +5 degrees
・Racing: -5 degrees
[Opening angle / Height] Free
[Handlebar locks] Available
[Handlebar stopper function] Available
[bearings]
・Under bracket side: Accessory
・Top bridge side: Stock to be reused
[Specification]
・Compatible with stock brake master
・Compatible with stock clutch holder
・Confirmed Brembo RCS brakes
・Stock light bracket, meter, horn, etc. can be used
[Components]
・Special meter brackets
・Exclusive collar set
*Brake / Clutch*
・Depending on the position, the oil tank and clutch wire may interfere with the meter cover.
・The brake hose needs to be changed to an aftermarket one or the routing needs to be changed.
*Wires*
・The accelerator wire, clutch wire, and switch cables need to be changed.
*Position Details*
・When installing the fork clamps, the clamp bolts should face outward with the handlebar clamp attachment pointing upward.
・The handlebar clamps face +5 degrees in the straddled position.
・Other positions cannot be installed as they will interfere with the stock blinkers.
*The direction of the vehicle is determined by riding on the vehicle.
*Compatible part numbers are different for Z900RS and Z900RS CAFE, so please check and purchase beforehand.
*This kit is specially designed for Z900RS CAFE with additional parts required for installation.For Z900RS without cowl, please purchase another part number.
*Z900RS CAFE has a limitation on the position to avoid interference with the stock blinkers.Please read the following notes before purchasing.
*Only Street Hi (stock) position is compatible.
・Since the master cylinder is close to the blinker, the installation angle of the master cylinder is limited.Adjust it so that it does not touch the blinker.(See image)
・In order to prevent interference with the cowl, the cowl, meter and light will be offset to the front.(See image)
・When installing the rearview mirror, it is required to remove the mirror clamps.Please note that the mirror cannot be replaced if it is fixed to the handlebar.Depending on the type of mirror, it may not be able to be installed due to interference with the cowl.
*The light bracket, meter, horn, etc. can be used with the stock products.
*Hole drilling to the handlebar is required to fix the switch box.
*Use the stock clamp bolts for the under bracket.
*Bar ends are not included and must be purchased separately.
*Installation requires specialized knowledge and tools, so please contact a professional shop for installation.
*The mounting mirror in the image is ZII type short bracket.
*Images may contain other products.
*The individual images are in color: Brown / Black.
*There may be changes in product specifications due to the manufacturer's reasons.