*FI (퓨얼 인젝션 차량) 원숭이는, 제너레이터 커버의 형상이 다르기 때문에 장착이 어렵습니다. 상당한 가공이 필요합니다.
[설치에 대해서]
이 상품은, 드라이브 스프로킷이 크게 바깥쪽으로 이동하므로 설치 엔진 발전기 커버의 일부를 삭리락토스 필요가 있습니다.
*FI (퓨얼 인젝션 차량) 원숭이는, 제너레이터 커버의 형상이 다르기 때문에 장착이 어렵습니다. 상당한 가공이 필요합니다.
* 표준에서의 오프셋 값은 26.5m와 18.5mm의 두 곳입니다. 그 외의 오프셋 값을 설정하려면 샤프트 스페이서를 가공해야 합니다.
* KEPSPEED사에서는 표준 오프셋 값 이외의 오프셋을 설정하기 위한 가공은 하지 않습니다.
*일부 중국제 엔진의 경우, 프로텍터의 고정이, 아래쪽 후방을 제외한 3곳 밖에 설정 가능하지 않는 타입이 있습니다. 그 경우는, 3곳 고정에서도 사용할 수 있지만, 프로텍터 플레이트의 가공 등은 하지 마세요.
*조립에 관한 설명서 (컴플리트 키트용) 가 첨부됩니다. 설명서를 참고로 신중하게 조립하세요. 단, 정비 작업상의 상식적 기법 등에 대해서는 설명서에 기재되어 있지 않습니다.
*오토바이 정비에 관한 경험자들이 맞붙을 수 있다 작업을 하세요.
*리어 서스펜션이 풀 최종 상태가 되어도, 비정상인 접촉 부분이 없는지 반드시 확인하고 주행하세요.
상품마다, 세세한 부분에서 약간의 사양 변경이 있는 경우가 있습니다. 소개영상과 다소 다른 점이 있습니다만, 실물을 우선으로 하오니, 양해 부탁드립니다.
*오토바이 정비 전문점에서 조립 작업을 부탁드립니다.
*주행 개시 후에는, 이른바 '초기 풀림' 발생에 유의하고 뜻밖의 트러블을 일으키지 않도록, 세세한 점검 실시하세요.
[제조업체 보증에 대해]
*수송 상의 문제로, 작은 기스와 찰과상이 발생하는 경우가 있습니다.
상품의 가치나 기능을 현저하게 해치는 불량품 이외는 메이커 보증 대상에서 제외합니다.
*상품 장착 후의 반품은 어떤 이유의 경우도 받아들일 수 없습니다.
그리고, 주행 시작 후의 트러블은 운전 상황 및 정비 상황, 혹은 차체 컨디션과 수급 불균형이 원인이 되는 일이 많고 상품 개별의 원인과 구별이 되기 어렵기 때문에 모든 면책으로 하겠습니다.
* 베어링 6001ZZ (양면 스티커) 의 품번의 물건을 사용하고 있습니다만, 교환품이 준비가 되어 있지 않습니다.
*메이커의 사정에 의해 상품의 사양변경이 있을 수 있습니다. 양해바랍니다.
* 해외제이므로 성형, 용접, 도장 등 제작이 허술한 경우가 있습니다. 또한 운송상의 문제로 작은 흠집이나 찰과상이 발생할 수 있습니다.
Country of origin :China
Manufacturer: KEPSPEED
[Notes on purchase]
*All GM-MOTO products are custom parts.Since these products are set up in response to the requests of heavy users, there may be parts of the product that change or decrease from the original driving performance.Please use as dress-up parts for show model machines.Therefore, it is not suitable for driving on public roads or tracks.In some cases, it may not be possible to mount the unit on a motorcycle, or adjustments and modifications may be required in various areas.
*It is difficult to install it on the fuel injection vehicle (FI) MONKEY because the shape of the generator cover is different.A lot of work is required.
[About the installation]
*Because the drive sprocket of this product moves outward greatly, it is necessary to cut off a part of the generator cover of the engine to be installed.
*It is difficult to install it on the fuel injection vehicle (FI) MONKEY because the shape of the generator cover is different.A lot of work is required.
*The standard offset values are 26.5m and 18.5mm.To set other offset values, the shaft spacer must be modified.
*KEPSPEED does not offer any machining to set an offset other than the standard offset value.
*On some engines made in China, the protector can only be fixed in three places except for the lower rear part.In such a case, the protector plate can be fixed in three places, but please do not modify the protector plate.
※Instructions for assembly (for complete kits) are included.Please refer to the instruction manual and assemble carefully.However, common sense techniques for maintenance work are not described in the manual.
*Please make sure that the person with experience in motorcycle maintenance performs the assembly work.
*Even if the rear suspension is at full bottom, make sure to check for any abnormal contact points before riding.
※There may be some minor specification changes for each product.There may be some points that differ slightly from the introduction image.
*Please have assembly work done in a specialist shop regarding motorcycle maintenance.
※After the start of riding, pay attention to the occurrence of so-called initial loosening and perform frequent inspections to prevent unexpected problems.
※Some minor scratches and scuffs may occur due to transportation issues.
※GM-MOTO does not accept returns for any reason after the product has been installed.
*In addition, problems after the start of riding are often caused by riding conditions, maintenance conditions, or a mismatch with the condition of the vehicle, and are difficult to distinguish from the causes of individual products. Therefore, all will be disclaimed.
*The bearing is part number 6001ZZ (sealed on both sides), but there are no replacement parts available.
*There may be changes in product specifications due to the manufacturer's reasons.
*Because it is made overseas, the molding, welding, painting, etc. may be insufficient.There may be some minor scratches and scuffs due to transportation problems.