[변위]115cc
[보어 직경]57mm
[압축 비율]11.5:1
[캠축]스포츠 캠축
- 이 제품은 재고 실린더 헤드에만 설치할 수 있습니다.
- 에이프100 (HC07-1600001- / HC13-1000001~) 모델은 전체 배기 가스 배출로 교체해야 합니다.
- 이 키트는 나열된 모델 및 프레임 번호를 가진 모델 전용입니다.. 다른 모델에는 설치할 수 없습니다.
- 이 키트를 장착하려면 엔진 탈거 및 기타 관련 작업이 필요합니다.. 이 키트가 의도된 모델에 대해서는 서비스 설명서를 참조하는 것이 좋습니다.
- 제품 설치 시 아래 설명된 공구를 준비하고 설치 지침을 주의하여 따르십시오.. 본 사용 설명서 및 Honda 정품 서비스 설명서는 기본 기술 및 지식을 갖춘 사람을 대상으로 합니다.. 설치 경험이 없거나 필요한 도구가 없는 경우 기술적으로 자격을 갖춘 상점에 문의하는 것이 좋습니다.
- 이 키트만으로는 APE가 제대로 작동하지 않습니다.. 카뷰레터 키트를 구입하십시오. (별도 판매). APE100 : 프레임 번호 HC07-1600001~ 및 HC13-1000001~은(는) 카뷰레터를 교체할 경우 배기 시스템 공급 파이프 브래킷에 방해가 됩니다.. 설치를 위해 전체 배기 시스템으로 교체해야 합니다.
- APE의 출력을 더욱 높이기 위해 SP Takegawa의 배기 시스템을 사용하는 것이 좋습니다.
- 일부 볼트, 너트, 노크 핀, 패킹은 재사용할 수 있지만, 심하게 마모되거나 손상된 볼트 대신 새것으로 사용하십시오.
- 액상 포장 등은 사용하지 마십시오.. 단연코. 오일 통로 등을 막을 가능성이 있고, 최악의 경우 엔진 파손 우려가 있다.
- L. 크랭크케이스 커버 개스킷 (혼다부품번호 11394-KN4-750) 이 제품을 설치하려면 별도로 필요합니다.. 따로 구매해주세요.
[Displacement] 115cc
[Bore Diameter] 57mm
[Compression Ratio] 11.5:1
[Camshaft] Sport Camshaft
- This product can only be installed on stock cylinder head.
- Ape100 (HC07-1600001- / HC13-1000001~) models must be replaced with a full exhaust exhaust.
- This kit is only for model with the listed model and frame numbers. Please note that it cannot be installed on any other models.
- Installation of this kit will require engine removal and other related work. It's recommended that you refer to the Service Manual for the model which this kit is intended.
- When installing the product, prepare the tools described below and follow the installation instructions carefully. This instruction manual and the Honda Genuine Service Manual are intended for people with basic skills and knowledge. If you do not have experience in installation, or if you do not have the necessary tools, we recommend that you contact a technically qualified store.
- The APE will not perform well with this kit alone. Please purchase the carburetor kit (sold separately). APE100: Frame numbers HC07-1600001~ and HC13-1000001~ will interfere with the exhaust system feed pipe bracket if the carburetor is replaced. It's necessary to replace with full exhaust system for installation.
- We recommend using SP Takegawa's exhaust system to further increase the power of your APE.
- Some bolts, nuts, knock pins and packing may be reused, but Make sure to use new ones instead of reusing those that are severely worn or damaged.
- Please do not use liquid packing etc. absolutely. There is a possibility of preventing the oil passage etc., and in the worst case, there is a fear of breaking the engine.
- L. Crankcase cover gasket (Honda part number 11394-KN4-750) is separately required to install this product. Please purchase it separately.