CB1300SB(2005 / It is SC 54). LED, Lens can be done with Bolt - on, but the attached Relay differs from the product image (The same applies to ManufacturerSite) It does not work at all with exchange. Owner before POSHRelay (090010-WR) Since it was already exchanged, Relay returned to POSH and it was OK to operate. However, there are times when it goes off once it continues to blink for more than 20 seconds in Left OnlyBlinker operation. Since Blinker operation never runs for a long time, it is good. (Because it is a used car, maybe there are other causes?)
I think that it is overwhelming if you think about the trouble of work.
I do not quite understand the high or low of the good or bad price of Brand. I do not know whether exclusive Relay is exclusively for this set or exclusively for the model.
Lens - Although I could put the LED on the pon, the attached Relay did not operate with just attaching, and a little processing was necessary. As processing contents, Relay's GND Wiring Is it the middle? It is necessary to extend and connect to the Gold part of the car body or to the - terminal of Battery.
I am between RelayBody and Connector (From Connector) We cut Wiring once and extended it with Cable of about the same thickness and bite it to the Screw part under Seat. Please do waterproof processing firmly for extension. (Processing is self-responsible at best. ) You can plug it if you have a matching terminal without cutting it, are not you?
Although it is about operation, other people also have a little Time lag as you said, let's put Blinker out with clearance. After turning off Blinker, I feel there is a lag even when the Position lamp lights up again.
I think the Position lamp is quite bright.View Detail
Received this product quickly and was very easy to install. The hardest part was to locate the OEM relay. Once I located it is was a matter of unplugging the OEM one and plugging the new one in. Works great. Instructions are in Japanese I had to translate. View Detail
I bought it because NORMAL Design is terrible. Installation is easy It's just that it's smaller than I thought it would be. It may be a little hard to see from the front, but the brightness of the LEDs works just fine!View Detail
I didn't like that protruding blinker, so I replaced it. It looks Refreshing, but it's pretty Smallish. I might have an accident one day and I'm going to put it back together.
Are you sure you're up for this? Go ahead.View Detail
I have no problems with the performance and texture. It's very good. ODAX's ICRelay "OX-K60-R. It emits light from inside to outside without any problems when used with
The problem is installation. The Honda Small Dice Bullet Terminal on the Blinker side (Male) It is not the same as the BlinkerCable's Bullet Terminal for the 2019 MODEL R25 is a general Bullet Terminal (Female) So, It is not possible to connect as is. The Bullet Terminal must be replaced separately. (Guaranteed to fit, though...)
Also, although the Front is a sufficient Cable length If you want to pull from the Rear OEMFender, you need to extend it by yourself because it's not long enough. In the case of a Fender Eliminator, for example, it would be Large.
The Blinker Base we bought together WMB-207066. We also had to deal with That will be noted in the Review there.View Detail
I chose this product for the Daylight and LED Blinker There is one more similar product, but it is more expensive because of its multifunctionality …
In this case, it's very inexpensive and very well made and very good in total with Rear! I think you should be comfortable with the Cowl removal and Wiring process for installation! If you're not sure, you could hire a motorcycle shop to do it for you
I can switch the Switch on and off in the middle of the car because the law has changed and it's suspicious I'm playing with itView Detail
?attachment The CBR650R is mounted at the same position angle as the NORMAL. However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away. I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose. ・NORMAL (Reserve integrated horizontal master) Impressions of No complaints on public roads. Familiar feel and very easy to handle. However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful. Radipon (Reserve separate body portrait master) Impressions of It was totally different from what I expected, my expectation was that it would feel like a Rear brake… It is really a mild and easy-to-handle radipon. On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN? But I felt the radipon effect from Breaking a little stronger, and It can be hung up to a hard brake without effort. I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。 Mount included with the BOLD. Microphone and speaker are not included and must be purchased separately.View Detail
일본
최대 쇼핑몰
전용 쿠폰,
세일
빠르고, 안정적인
배송