Beautiful. [Color] You can makeover by simply changing the blinker lens with the smoke level. To change the front and back, use Quantity:You need 2 sets, but I think the gold amount is cheap.
View Detail
- Instock
19,970.58 KRW (2,131 엔)
Webike Point: +21 pt
(196.8 KRW)
배송정보
In Stock : 2 left, Ships within 24 hours.
Estimated arrival date around
FITMENT
KAWASAKI
Open Fit Model Information Table
-
NINJA650R
09-11 *Fits rear only
-
VERSYS1000
12-14 *Fits both front and rear
-
VERSYS650
10-13 *Fits both front and rear
-
NINJA250R
FNO, EX250L-000001-010999 *Fits rear only.
전체보기
KAWASAKI
아래 상품 설명은 Google에 의해 자동으로 번역됩니다.
Product detail
타입:훈제
좌우 1세트
*
*윙커 공은 정상을 다시 사용합니다.
*다음 차량은 리어만 적합합니다. NINJA250, ER-4N, NINJA400R, NINJA ZX-6R, ER-6F, NINJA650R, NINJA650, NINJA1000, Z1000.
노멀의 렌즈를 교환하고 깔끔한 드레스 업 부품입니다. 신호 공은 정상을 사용합니다.
주의
* 사용 설명서가 포함되어있는 경우, 일본어로 표기됩니다.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
고객 구매후기
Reviews with image
Fits:KAWASAKI ER-4N All models of ER400B *Fits to rear only, KAWASAKI Z250 All ER250C models *Fits both front and rear, KAWASAKI Z1000 10-13 *Fits rear only, KAWASAKI ER-6F 09-10 *Fits rear only, KAWASAKI ZrX1200ZrX1200 DAEG FNO
Fits:KAWASAKI ER-4N All models of ER400B *Fits to rear only, KAWASAKI Z250 All ER250C models *Fits both front and rear, KAWASAKI Z1000 10-13 *Fits rear only, KAWASAKI ER-6F 09-10 *Fits rear only, KAWASAKI ZrX1200ZrX1200 DAEG FNO
Apr 3, 2016
I replaced Blinker lens this time. Because the car body is GraphiteGray, I thought that it was too dark ~, but I tried wearing it, but it was not so, it was a tightened. It was easy to install. However, I use Phillips Screwdriver when wearing, but please be careful not to slip Screw.
Products are recommended.
Helpful?
Fits:KAWASAKI ER-4N All models of ER400B *Fits to rear only, KAWASAKI Z250 All ER250C models *Fits both front and rear, KAWASAKI Z1000 10-13 *Fits rear only, KAWASAKI ER-6F 09-10 *Fits rear only, KAWASAKI ZrX1200ZrX1200 DAEG FNO
Apr 14, 2015
It became always bright with Blinker Bulb Positioning, and it was introduced to make it a bit darker.
Quantity : In 4 Set it was further hit by 5% Off and I bought the bride's ER-6f. Exchange + Screw (Short + 2nd Driver is easy to do) Just remove the Lens and replace it. When removing, Guide on the root side (Place of protrusion) Do not pull it out because it is out there. It is good to pull Lens up while pressing Reflector side in.
Inlay is easy, but the final Screw tightening is over-tightened. It is enough to tighten 45 ° from where Lens - Reflector - Body gap disappears.
When I exchanged, Normal lens was in it with Crack.
The appearance after replacement is as shown in the photograph. I think that it was tightened personally.
Blinker Bulb has been replaced with LED bulb.
There was not much change in visibility from the front or the side. As the light to the back of the front Blinker was reduced, the desired effect was obtained.
Helpful?
New Custom Articles
