I installed this on my 2001 dTRACKER.
Bolt at the attachment point to the vehicle body is M6 and Quantity:2pc and M8Quantity:2pc only.
The carrier itself looks sturdy, but I'm not sure I'd be able to carry a full set of camping gear in a box like this.
I think it is better not to load the cargo without Brown too much.
- Instock
116,891.92 KRW (12,480 엔)
Webike Point: +125 pt
(1,170.79 KRW)
배송정보
In Stock : 2 left, Ships within 24 hours.
Estimated arrival date around
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
고객 구매후기
Reviews with image
![since area is also large and iron -- firmly .
<br>large load and what with are cinch. [ like a box ]
<br> It merely has, since the hand is small, it pushes, and it is hard to carry out influence just for a moment.](https://img.webike-cdn.net/photo/article/31/1355502588331M.jpg)
![[Webike Monitor] There is no place protruding on the <br>top face, and since it is flat, it is very easy-to-use.
Paint application is also good and it feels the conscience of a Manufacturer for the hole of a scupper being open to each Pipe.
Attachment was](https://img.webike-cdn.net/photo/article/24/1331449881324M.jpg)
![Storage of a motorcycle is under a carport. <br>Coating of the end of a square pipe will begin to break after use in about four years. A part of coating will separate in five years, and it is rust generating. <br>Comparatively [ back long ], a carrier has](https://img.webike-cdn.net/photo/article/98/1279368687198M.jpg)
Fits:KAWASAKI KLX250 , KAWASAKI D-TRACKER -07
Sep 1, 2021
Unbrowned loads are unsettling.
Helpful?
Fits:KAWASAKI KLX250 , KAWASAKI D-TRACKER -07
Oct 7, 2011
I also regard a load carrying face product as it being large and cost performance being good.
I think that it is a carrier suitable for the direction of the touring subject of a stopping cliff.
For the moment, it does not shake.
Helpful?
Fits:HONDA XR400 Other information]T-2, HONDA XR250 95 -, HONDA XR250 BAJA 95-
Apr 10, 2022
We chose this one because we wanted to increase Frame rigidity by integrating it with the Sub-frame, even if it increased in weight.
The installation of the Seat was done by inserting a washer in a hurry because the collar was not thick enough to hold the Seat together and the installation part started to bend during temporary tightening.
The hole positions are perfect, and it would be perfect if there were additional thicker colors in the Included Parts:section.
Helpful?
Fits:SUZUKI RMX250S 96-
May 4, 2020
Installation is odd but very easy to use
I wanted to add the GIVI MonokeyPannier that I'm using on my ZX11 I bought it as a base The installation is two Bolts for the installation of Small Bag and Seat & Side cowl installation BoltQuantity:Pair (for Left and Right) (For Bolt length change, it comes with the product), but you can use the Accessory Case side When you install from Bolt, the position to put the Bolt of Seat and co-tightening is about 3cm above Gap The order is to put in the Seat and the Bolt side of the co-tightening, then the Accessory Case side As an order, put in the Bolt side of the Seat and co-tightening first, then the Accessory Case side Put the bolt of the Seat side If you don't do the same order of tightening, the bolt of Seat side will be broken It may be a bit dull, but the bolt of Seat side is the standard, and the bolt of the Accessory Case side is more than appearance Secure it at an angle that rises to
I'm using this with a Mount base for Monokey in my Pannier It is very rigid and of good quality and does not wobble at all There are also enough of them for Carrier to get full marks
Helpful?
Fits:KAWASAKI
Dec 20, 2019
I installed it on KSR110 It could be installed on Smooth without Gap of the bolt hole at the time of installation
It looks solid and strong
Helpful?
New Custom Articles
