프레임 가드

ZETA Zeta Frame guard
Item Number:ZE52-0019
■Type:Material:5000 Series Aluminum Alloy


Remarks.
Please note:This product is not compatible with your vehicle.

Because the car body is rounded slightly at NORMAL, the feeling of Hold is not bad for Off-road boots, but by attaching this Frame guard, the Hold property rises markedly.

In my riding method, footpeg and Step plate are important parts for Machine control, it is a foot belly, Heel and ankle, and it holds at various foot parts, but Frame guard is By attaching, the thickness also increased slightly, the area to be Hold increased, making it very easy to control. Although it is Standing, it is easy to get on because it has a solid feeling of Hold during Jump.

Installation method, but the installation manual was not enclosed.
I could judge by Pitch of Bolt hole of product so there was no problem but I think that Manual should be attached.
Body Right Side Quantity Heol Guard's Bolt : Remove 2 pc, add the attached Bolt to Quantity : Just tighten 2 pc.
Left Side removes the Drive sprocket cover, removes the Bolt of the Sub Frame, inserts it obliquely from the Driven Sprocket side, and tightens the Bolt of the Sub Frame. Tightening Torque, like OEM, 2. 7N - I closed with m. I think that it should be written for those who do not have a service manual in Manufacturer.

For me, rather than Frame guard, the meaning of the Step plate is Large.

As the sense of unity with Motorcycle increases, operability improves so it was perfect for me who is an off-road beginner. It is especially recommended for people who want a sense of unity with the body when the car body runs ramping when you run off-road, or those who are suffering from Control.

Fit perfectly on my old WR250X. Easy to install. High quality. Incredible look. I have been looking for those protections since a while. I Bought a lot of zeta products that you can see ont the pics, always amazing. Fast shipping to France and great professionalism from webike. Thanks a lot.

I purchased this product to prevent scratches caused by off-road boots on my wr250rAluminum Frame.
I think this product will prevent scratches caused by Boots.
However, this product itself has no BALI, but the Edge is standing up, so if I installed it directly, the Frame would be scratched by this product. I hurriedly bought SpongeSeal at a nearby Home center and attached it to the back of the frame.
The thickness of the SpongeSeal used is 5mm, for reference.

Other than that, no complaints!
The Frame of R is Silver, so it is not noticeable, which is good.
I don't know if X is necessary since it is MOTARD to begin with, but I think it will stand out since it is FrameBlack. I think there are different tastes here.

[How is it used?
It may not be obvious to modern Kawasaki riders, but the Kawasakis of these days are amazingly well Rusted!
I bought this because I wanted to protect my old KDX220SR Frame from Boots etc. when playing in the mountains.

Was the one you received as per Image?
It's a good feeling to cover a wide area around footpeg as Image.

Was the installation difficult?
Because the installation of the vehicle body Right Side is only tightened with the Master Cylinder of Rear brake, the front side is not enough.
Moreover, the hole for the bolt installation was slightly gaping, and the bolt that stopped the Master Cylinder of my KDX that I bought used was slipping, so I had a hard time. It is a place where I want you to work a little harder.

How was your experience with it?
The Guard range is also very wide and thick, so it's perfect for Frame protection.

[Included Parts:were they on?
Aluminum board as frame guard is Quantity:Pair (for Left and Right) Quantity:Only 1pc. each, not even the Bolt for Replacement is included.
For the price, why not include a good looking Bolt and a Rubber sheet etc. that can be attached to the back?

[Was there anything that disappointed you?
The hole for the Bolt was slightly Gap.
If you install the Guard as it is, there are some places where the Guard itself hits the Frame and the Frame's paint peels off (Rubber sheet has been attached to prevent this).

0Other items that may be useful include
Point and hang of installation
I think that it is better to protect the part that touches directly with Rubber sheet etc. to avoid crying afterwards.

[Availability and clarity of the Instruction Manual
You don't need to check the Instruction Manual. It only sticks there." This product is easy to understand because it is Design.

[Notes]
Tentative assembly in advance as above. "Bolt hole confirmed." When "Protecting areas that might interfere with the Frame." Make sure to do the following

[ITEMS TO BUY TOGETHER
If you have Double-sided Tape and thin Rubber sheet, it is easy to make a countermeasure, and if you have Stick File (thin round stick type), it is safe in case of a hole gap.

[Opinions and requests to Manufacturer
Please make the product a little more productive.