I decided to go with Active's Fender Eliminator Kit because I plan to install a NumberSIDEBlinker in the future!
The Rear looks tighter!
194,420.31 KRW (20,746 엔) 201,486.39 KRW Save 4%
Webike Point: +207 pt
(1,939.89 KRW)
배송정보
This item is discontinued.
FITMENT
KAWASAKI
Open Fit Model Information Table
-
Ninja ZX-25R
20-22
-
NINJA ZX-25R SE
20-22
-
Ninja ZX-4R SE
23-24
-
Ninja ZX-4RR
23-24
아래 상품 설명은 Google에 의해 자동으로 번역됩니다.
Product detail
칼라:블랙
번호 등:LED번호 등부
넘버 각도:40°
차량 검사 대응
**정품 적재 후크를 이설하여 장착할 수 있습니다.
*별도 판매의 리플렉터 킷트가 필요합니다.
*차량검사증에 기재된 차량전장에서 ± 30mm이상 변경시 구조변경이 필요할 수 있습니다. 차량검사장에서 지시가 있을 경우 검사관에 따라 기재사항을 변경하시기 바랍니다.
*메이커의 사정에 의해 상품의 사양변경이 있을 수 있습니다. 양해바랍니다..
차체에 가공이 필요 없이 정상 방향 지시등의 설치는 물론, 장착 위치 및 스테이 형상까지 고집하다, 스타일리쉬하고 차량 검사에 대응하는 펜더 레스 키트입니다.
주의
* 사용 설명서가 포함되어있는 경우, 일본어로 표기됩니다.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
고객 구매후기
Reviews with image
Fits:KAWASAKI Ninja ZX-25R 20-22, KAWASAKI NINJA ZX-25R SE 20-22, KAWASAKI Ninja ZX-4R SE 23-24, KAWASAKI Ninja ZX-4RR 23-24
Nov 15, 2021
Helpful?
Fits:KAWASAKI Ninja ZX-25R 20-22, KAWASAKI NINJA ZX-25R SE 20-22, KAWASAKI Ninja ZX-4R SE 23-24, KAWASAKI Ninja ZX-4RR 23-24
May 22, 2021
It was easy to install even for a beginner.
It is good that Loading Hook can be relocated.
Helpful?
Fits:KAWASAKI Ninja ZX-25R 20-22, KAWASAKI NINJA ZX-25R SE 20-22, KAWASAKI Ninja ZX-4R SE 23-24, KAWASAKI Ninja ZX-4RR 23-24
Dec 19, 2020
Good attention to load hanging.
Weight excluding common parts
OEM1060g
This product 265g (without load hangingParts)/335g (with load hanging parts)
Weight of Plate+Hook of diverting parts for loading is 155g
Loadability
If you put a strap etc. through the hole on the side, it is possible to tie it tightly without the load hanging parts.
The load-bearing capacity is stronger if you use the load-bearing parts because they are made of steel, but it seems to be able to endure without them if the load is not extremely heavy.
● Mounting
Installation and fitting is good.
When I tried to install the License Plate Holder with a rim, it interfered with the License Plate Light, so I shaved the screw hole about a half inch wider.
The instruction manual says to install the ETC bracket with the bolt on the outside of the car, but if I follow the instruction manual, the ETC bracket will not be attached.
I took off the Bracket and threw in the ETC as it was because I was refreshing the Bolt outside the car.
It is instructed to seal the gap of the Cable hole with Sponge sheet, but it is planned to seal it with the gap Pate of the Air-conditioner because it is defeated by the tension of Cable and becomes crumpled.
It is better to fix the cable with the Cable Fixing Bracket than the Tie Wrap as instructed.
●Textures
It is made by cutting and bending a board, so it is less luxurious than Cut-out's product, but it is necessary and sufficient.
Helpful?
Fits:KAWASAKI Ninja ZX-25R 20-22, KAWASAKI NINJA ZX-25R SE 20-22, KAWASAKI Ninja ZX-4R SE 23-24, KAWASAKI Ninja ZX-4RR 23-24
Oct 25, 2020
It is very lightweight.
It can also mean how heavy the OEM FenderUnit is.
Smallest build required, and the texture of the Anodized is also very good.
I installed it with LED License Plate Base.
The OEM Blinker Bracket was not needed.
Reflector is treated as an option, so I wanted the same thing to happen here.
Helpful?
New Custom Articles
