I've used their Caliper support in the past.
Again, the Center came out well with the pimping and no problems at all.
It also comes with a Shim for adjustment, but I didn't need it at all.
It looks chic and Large satisfied.
- Instock
142,258.76 KRW (15,180 엔)
Webike Point: +152 pt
(1,424.46 KRW)
배송정보
In Stock : 2 left, Ships within 24 hours.
Estimated arrival date around
FITMENT
YAMAHA
Open Fit Model Information Table
-
SRX400
85-86
-
RZ350RR
84
-
T MAX
04-07
-
SRX600
85-86
전체보기
YAMAHA
아래 상품 설명은 Google에 의해 자동으로 번역됩니다.
Product detail
[프런트용]
재질:알루미늄 2017S (양은 처리)
칼라:블랙
대응 캘리퍼:brembo산 40mm
대응 로터:스탠다드 φ 267더블 디스크
부속품:캘리퍼 마운트용 스테인리스 볼트, 0.5mm적 조정
**40mm속도 대응 캘리퍼 지원은 모두 "brembo산 40mm캐스팅 캘리퍼" 에서 설계하고 있습니다. 26.5mm의 오프셋 센터에 있어, AP, NISSIN제의 캘리퍼에 사용하는 경우는 부속의 심에서 조정을 하세요. (6POT캘리퍼에는 대응하지 않습니다.)
*캘리퍼 개체의 제품 오차 수정도 부속의 심이 유효합니다.
*캘리퍼와 로터의 변경으로, 로터라고 패드의 타격 면이 달라집니다 이 경우, 패드의 로터에 해당되지 않는 면을 삭리락토시서 사용하세요.
*캘리퍼 볼트 피치 brembo 40mm:P1.5, brembo 65mm:P1.25, NISSIN:P1.25, TOKICO:P1.25
*brembo산 65mm속도 2PAD캘리퍼에는 사용할 수 없습니다.
*사진은 이미지입니다..
장착 속도가 40mm와 65mm의 캘리퍼를, 스탠더드 로터 사이즈로 조합하기 위한 캘리퍼 서포트.
재질은 알루미늄 깎는 구실로 양은 처리를 할 높은 강도·고 내구성을 확보했습니다.
주의
* 사용 설명서가 포함되어있는 경우, 일본어로 표기됩니다.
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
고객 구매후기
Reviews with image
Fits:YAMAHA XJR400 93-96, YAMAHA XJR400S 94, YAMAHA FZ-6N 04, YAMAHA FZ6-S FAZER 04, YAMAHA FZR250R 89-99
Jun 27, 2021
Helpful?
Fits:YAMAHA XJR400 93-96, YAMAHA XJR400S 94, YAMAHA FZ-6N 04, YAMAHA FZ6-S FAZER 04, YAMAHA FZR250R 89-99
Jun 9, 2020
I used it on my RZ250RR
I'm happy with the Center without Shim!
I recommend it because it looks good and isn't expensive
I've got over a thousand miles on it now and no complaints
Helpful?
Fits:YAMAHA XJR400 93-96, YAMAHA XJR400S 94, YAMAHA FZ-6N 04, YAMAHA FZ6-S FAZER 04, YAMAHA FZR250R 89-99
Sep 15, 2017
When using Support, Caliper seems to be hanging in many cases, so it was a bit uneasy to install, but I felt relieved that the position did not go down to that point.
Because Front fork 's Bracket is Black, I chose Black Anodized, but it was Large Correct Answer. I looked nice and did not have much afterthought, so it was good. There is a slight gap between Bracket and Support, but I felt that Parenthesis is good in reverse.
Let's put the Center firmly in place when installing. There are quite a few individual differences in vehicles. It is safe because it comes with Shim which seems to be sufficient.
However, because the attached Caliper bolt can not be felt like for building materials, I replaced it for Taper type. Although it said, although it searched quite a lot, I think that there are almost no choices of Bolt.
Helpful?
Fits:HONDA CB400SF Version S 96 (Not available after 1997), HONDA CB1100 10-17, HONDA CBR900RR 92-97, HONDA VTR1000F 97-03, HONDA HORNET600 98-03
May 19, 2022
Quality is excellent, but there is a problem with the Position
The quality is excellent and the Brembo caliper comes to the center perfectly without shim without error.
However, note that the Support is much lower than the Normal caliper, so the hose length will be about 5 cm shorter than the Normal. I use Daytona's extended hose.
It looks like AGRASSupport's position is not that different from Normal caliper for less Offset.
Helpful?
Fits:YAMAHA TZR250 89-95, YAMAHA RZ250RR 84-87, YAMAHA RZ250R 88, YAMAHA FZX750 90-93, YAMAHA FZR400RR SP 90-94
Jan 11, 2022
Front forkTZr on RZ250 (3ma) I purchased this product to equip a Brembo caliper to a vehicle of
The texture is good and fitting is no problem.
I think it looks good with the meat removed.
Helpful?
New Custom Articles
