Item ordered on 24th. Mailed on 25th. Reached Singapore on 27th. Japan efficiency . Itwm bubble wrapped and boxed. No damages .
View Detail
- Instock
35,320.47 KRW (3,771 엔)
Webike Point: +38 pt
(355.92 KRW)
배송정보
In Stock, Ships within 24 hours.
Estimated arrival date around
FITMENT
HONDA
-
CB400SF
99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID)
-
CB400SF
08-21 NC42 VTEC Revo *Requires switch hole drilling|*Requires side cap (for inner diameter 18mm)
-
CB400SF
-98 NC31 *Processing of switch hole required|* Required side cap (for 18mm ID)
-
CB400SS
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
전체보기
HONDA
YAMAHA
-
XJR400R
01-07 RH02J *Processing to open switch hole required|*Side cap required (for 18mm diameter)
-
XJR1300
07-12 (RP17J) *Processing to open switch hole required|* Required side cap (for 18mm ID)
-
XJR1300
00-06 (RP03J) *Processing to open switch hole required|*Side cap required (for 18mm ID)
-
TW225E
00- (Disc Brake Car) *Processing of switch hole is required
전체보기
YAMAHA
SUZUKI
-
GRASS TRACKER
09-12 09-12(FI cars)*Side caps can be used with the stock ones.
-
GRASS TRACKER
-08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
-
GSX400
05-07 GK7CA *Processing of the switch hole is required|* You can use the normal side cap.
-
ST250 E Type
-07 NJ4AA *Processing of switch holes required|* Normal side caps can be used.
전체보기
SUZUKI
KAWASAKI
-
ZRX400
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
-
ZrX1200ZrX1200 DAEG
*Requires drilling of switch hole| * Requires side cap (for 18mm diameter)
-
ZRX1200R
*Requires drilling of switch hole| * Requires side cap (for 18mm diameter)
-
ZRX1100II
*Requires drilling of switch hole|* Requires side cap (for 18mm diameter)
전체보기
KAWASAKI
Others
Open Fit Model Information Table
-
Universal
아래 상품 설명은 Google에 의해 자동으로 번역됩니다.
Product detail
핸들 칼라:블랙
[운전대 사양]
핸들:철제 블랙/바깥 φ 22.2mm/안지름 φ 18mm
케이블, 호스류는 정상적인 채로 설치 가능
[핸들 크기]
전체 높이:80mm
전폭:680mm
홀더 장착부의 유효 폭:125mm
풀백 사이즈:155mm
내 입 각도:28번
앞으로 기운 각도:65번
*
*사진 중 핸들 클램프 (홀더 또는 포스트) 등은 상품에 포함되지 않습니다.
*사이즈 표기는 수평 때의 것입니다.
*차 검증에 기재된 차체 크기에서 높이±40mm폭±20mm를 넘는 변경이 있는 경우는 구조 변경의 신청이 필요합니다..
케이블 등 옵션 부분 목록은 이쪽
멍키 손잡이 고리는 이쪽
다른 염색은 이쪽
7/8인치 로드 모델의 노멀 핸들 크기 목록
7/8인치 스쿠터/아메리칸 모델의 노멀 핸들 크기 목록
1인치 아메리칸 모델의 노멀 핸들 크기 목록.
일본산. 시작, 장착 확인, 양산, 일관하고 자사에서 관리 히가시오사카에서 오래 기른 기술과 노하우로 소재의 엄선, 몇가지의 연마, 품번의 각인, 고 정밀의 휨 가공, 용접, 고품질인 표면 처리 등 많은 고집이 막힌 핸들 바입니다. 인장 강도에 뛰어난 STKM13A스틸 재료를 사용. JMCA안전 기준치 클리어. 블랙 크롬 도금의 위에서 아크릴 페인트의 이중 방수 처리를 하고 있습니다.
주의
* 사용 설명서가 포함되어있는 경우, 일본어로 표기됩니다.
MODEL PAGE LINKS
HONDA
- APE50
- APE50
- MONKEY
- MONKEY
- APE100
- FTR223
- FTR223
- VTR250 (MC33)
- VTR250 (MC33)
- HORNET250 (CB250F)
- CB400SS
- CB400SF (Super Four)
- CB400SF (Super Four)
- CB400SF (Super Four)
- CB400SF (Super Four)
- CB400SF (Super Four)
- CB400SB (Super Bol D'or)
- NC700S
- NC700X
- CB750
- CB1100
- CB1300SF (Super Four)
- CB1300SB (Super Bol D'or, CB1300S)
- CB1300SB (Super Bol D'or, CB1300S)
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
NEW ARRIVALS IN USED PARTS FOR
New arrivals in used
New arrivals in used
고객 구매후기
Reviews with image
Fits:HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC II* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID)
Installed on: YAMAHA MT-25
Fits:HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC II* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID)
Nov 9, 2018
HURRICANE BM Continental 3 Type Φ7/8-inches Handlebar Steel
Been using this handlebar for a few months and it is much better than my previous wide handlebar. The sweep back angle and height brings the handlebar closer to my body and easier for maneuvering. The shorter length from end to end and the sweep back angle towards me makes it alot more easier for lane splitting. All in all better posture and handling for urban riding.
View DetailHelpful?
Fits:HONDA CB750 04- RC42 *Processing of switch hole required|* Required side cap (for 18mm ID), HONDA FTR223 (without side numbers) * Requires modification of the clutch cable and choke cable., HONDA CB400SF 99-07 NC39 VTEC III* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC II* requires drilling of switch hole|* requires side cap (for 18mm ID), HONDA CB400SF 99-07 NC39 VTEC *Processing of the switch hole is required|* Required side cap (for 18mm ID)
Nov 12, 2017
Since it was 163 cm and Small handle, I felt Handlebar was a bit far and low, so I exchanged it. Harness and Wire had plenty of time, but since Brake hose was feeling Limit even at NORMAL, I searched for the range where the Large Year Position does not change and made it to this Handlebar.
Because it is a Universal Product, install mounting hole of vibration proof material Quantity : Pair (for Left and Right) Quantity Pin hole of Switch box with 2 places : Pair (for Left and Right) You need to be able to open one place at a time. The dimensions from the end and the vibration isolating material mounting hole are Quantity : 2pc. Care must be taken so that the hole position of Set is 180 degrees relationship. The position of the hole in the Switch box, after positioning the Handlebar and Lever correctly, put Pin in red and marked the Handlebar and opened it. I did not need it because it was remodeling so that the parking brake can be operated with Lever, but NORMAL also needs to open the pin hole of the bar KingBrake.
Brake hose was in a state of being sticking unless you remove what is fixed at the Upper clamp.
I thought that Grip is ahead better, but I think that it is impossible to replace Brake hose any further, because it is ABS, so I am not confident of bleeding at the time of replacement.
Helpful?
Fits:SUZUKI GRASS TRACKER 09-12 (FI car)*You can use stock side caps., SUZUKI GRASS TRACKER Big Boy -08-8(Carburetor)*Drilling of switch hole is required|*You can use stock side cap. |*It is necessary to change the direction of the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo., SUZUKI GRASS TRACKER -08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
Aug 22, 2024
Good handlebar at a great price.
I wanted a narrower lower handlebar for my SR500. This one is economical, fits great and the chrome is top quality. I will be considering the Hurricane brand from now on when shopping for handlebars.
View DetailHelpful?
Fits:SUZUKI GRASS TRACKER 09-12 (FI car)*You can use stock side caps., SUZUKI GRASS TRACKER Big Boy -08-8(Carburetor)*Drilling of switch hole is required|*You can use stock side cap. |*It is necessary to change the direction of the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo., SUZUKI GRASS TRACKER -08 (Carburetor)*Drilling of switch holes is required. |*It is necessary to change the throttle cable, clutch cable and brake hose. |*It is necessary to change the direction of the brake banjo.
Apr 15, 2020
I think I failed to use it on the W800
I've been using the EZ-FIT-Bar, but I just need a little more height! And greedy
I purchased this product
The quality is good with no plating irregularities and no surface scratches
400ccClass for Replacement compatible Pipe Handlebar I think the width is just right for the
However, this width seems to be narrow when it is W800 used this time, and it becomes a tight position around the shoulder
I ended up having to go back to the EZ-FIT-Bar I bought last time
Well, it's a MotorcycleParts-esque story
As for the products themselves, they manufacture and sell a wide variety of Pipe Handlebar It's only HURRICANE
Very good product quality and I would recommend it to anyone
That's why I was a little disappointed (Lol)
Helpful?
New Custom Articles
